Unbricking

From Sharpfin
Jump to navigation Jump to search

Introduction

This procedure will take you through the restoration of your radio using a simple JTAG cable, with software we have provided.

Prerequisites

In order to recover a bricked radio, you will need:

  • JTAG cable
  • Software for flashing over JTAG
  • An image to flash to the radio
  • A lot of patience

JTAG Cables

'Wiggler' compatible cables are a popular low-cost cable, and well supported by the free jtag tools. Plans to make your own are widely available, and prebuilt ones can be found cheaply on ebay and similar sites. A "universal" wiggler will come with bare wires which can be soldered to the jtag test points on the barracuda board.

Wiggler Schematic

Jtag-soldering.jpg

JTAG Flashing Software

The application sjf2410, along with the error correction code from the linux kernel have been modified to produce a bespoke utility for the baracuda module's NAND flash. It uses the wiggler cable in the parallel port.

This version of sharpflash supports reading and writing of the NAND flash using the wiggler parallel port interface.

Reading Flash Images

At present, we are trying to identify the association between 'nanddump' images, Reciva upgrade images, and JTAG acquired images. We recommend taking a 'nanddump' (see Making a backup) of your radio as soon as possible, as it is our goal to be able to restore these images. Until then, you can make a back-up of your flash via JTAG using the following format commands:

sharpflash r kernel-mtd1.bin 004000 0fc000

Will extract the contents of the kernel partition into 'kernel-mtd1.bin', skipping any bad sectors as it goes. The program will also create 'rawdata.bin' and 'rawdata.ext' which contains the raw data and extended data information. Have a look at Reciva NAND Flash for the background on the flash structure.


Sharpfin Flash Programmer - http://www.sharpfin.zevv.nl/
.
Found S3C2410 processor on JTAG Cable
Found K9F2808UOC on processor
Reading NAND Flash:
 destination   = kernel-mtd1.bin
 raw data      = rawdata.bin
 err data      = rawdata.err
 start addr    = 0x4000
 length        = 0xFC000
.
Address  Progress                          Remaining
-------  --------------------------------  ---------
0000000  rrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrr    9h 12m
0004000  rrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrr    9h 11m
0008000  rrrrrr

Getting Bad Block Information

This is not needed for programming, however it is recommended that you keep a record of the bad blocks marked by the manufacturer as bad, because this information is stored in re-programmable memory, and it may be useful to be able to distinguish between manufacturer-defined bad blocks, and user-defined bad blocks.

sharpflash b

The program will output several lines, with each '.' representing a 16K block which is marked as good, and a 'b' fir each block which is marked bad.


Sharpfin Flash Programmer - http://www.sharpfin.zevv.nl/
.
Found S3C2410 processor on JTAG Cable
Found K9F2808UOC on processor
Checking NAND Blocks
 0000000: ................................................................
 0100000: bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb...............

Writing Flash Images

This process takes a long time to run - roughly 80 seconds per 16KBytes, so a full 16Mb flash will take about 24 hours.

sharpflash w mtd.bin 000000 0F00000

Will write an entire image from the file mtd.bin, and will produce an output similar to this:

Sharpfin Flash Programmer - http://www.sharpfin.zevv.nl/
.
Found S3C2410 processor on JTAG Cable
Found K9F2808UOC on processor
Writing NAND Flash:
 source      = mtd.bin
 start addr  = 0x0
 length      = 0xF00000
.
Address  Progress                          Remaining
-------  --------------------------------  ---------
0000000  wwwwwwwwwwwwwwwwwwwwwwwwwwwwwwww   21h 12m
0004000  wwwwwwwwwwwwwwwwwwwwwwwwwwwwwwww   21h 11m
0008000  wwwwwwwwwwwwwwwwwwwwwwwwwwwwwwww   21h 09m
000C000  wwwwwwwwwwwwwwwwwwwwwwwwwwwwwwww   21h 08m
0010000  wwwwwwwwwwwwwwwwwwwwwwwwwwwwwwww   21h 07m
0014000  wwwwwwwwwwwwwwwwwwwwwwwwwwwwwwww   21h 05m
0018000  wwwwwwwwwwwwwwwwwwwwwwwwwwwwwwww   21h 04m
001C000  wwwwwwwwwwwwwwwwwwwwwwwwwwwwwwww   21h 02m
0020000  wwwwwwwwwwwwwwwwwwwwwwwwwwwwwwww   21h 01m
0024000  wwwwwwwwwwwwwwwwwwwwwwwwwwwwwwww   20h 59m
.....

Interesting Information / Links